Skip to content
Spray foam and insulation services for Hartland and Wisconsin's Lake Country
Blown-in insulation installed to cold-climate depth in a Hartland, Wisconsin attic

Home / Services / Blown-In Insulation

Residential & Commercial

Blown-In Insulation in Hartland, WI

Blown-in cellulose and fiberglass for cold-climate attics and retrofit walls, installed to a measured depth across the Lake Country.

Blown-in insulation is the workhorse of attic upgrades in Hartland. It flows over and around ceiling joists, wiring, chimney chases and the odd framing details that make batt insulation leave gaps, and it installs fast enough to keep the project affordable on larger attic floors. In a climate zone 6A winter, where the attic floor is the main line between the heat you pay for and a vented attic at outdoor temperature, depth is what matters, and blown-in material is the most practical way to get there. Hartland Spray Foam Insulation installs both cellulose and fiberglass, and we recommend foam only when the assembly actually calls for it.

Cellulose or fiberglass in a cold climate

Blown-in cellulose is made from recycled paper treated for fire resistance. It packs densely, restricts air movement through the material better than fiberglass, and covers irregular framing tightly, which matters in older Hartland attics full of cross-bracing and odd bays. Blown-in fiberglass is made from spun glass fibers, absorbs essentially no moisture and holds its loft well over decades. Both are proven cold-climate attic materials. Cellulose usually delivers more R-value per dollar installed; fiberglass settles less and stays drier if the attic ever sees a roof leak. We carry both and will tell you plainly which fits your attic and budget.

Depth is the job: R-value explained plainly

R-value measures resistance to heat flow: the higher the number, the slower your heat escapes through the ceiling. For blown-in products, R-value comes from depth, so a Hartland attic targeting R-49 to R-60 needs roughly 14 to 20 inches of material depending on the product, full stop. That is why we install to a measured depth rather than by the bag count or the look of it. Depth markers go in across the attic so you can verify the coverage after the crew leaves, and the written estimate names the target depth before work starts. Many pre-1990 Lake Country homes carry a fraction of that depth, and even newer construction often stops at minimum code.

Top-ups of existing attics

If your attic already has insulation that has settled thin but is still dry and clean, a top-up adds new material over the old to bring the total depth to target. It is one of the most affordable winter comfort upgrades available for older Hartland homes, and it directly reduces the attic heat loss that feeds ice dams. Before any top-up we check for two things: air leaks at the ceiling plane, which should be sealed first so the new depth actually performs, and moisture or pest damage in the existing material, which means removal instead of a top-up. Ventilation gets protected too, with baffles at the eaves so the soffit vents stay open under the new depth. See our attic insulation page for the full picture on cold-climate attic assemblies.

Dense-pack blown-in for retrofit walls

Older wood-frame homes across Hartland, Merton and Nashotah often have empty or underfilled wall cavities, and you feel it every January as cold exterior walls and rooms that never quite warm up. Dense-pack blown-in cellulose or fiberglass fills those walls through small, patchable holes, drilled from inside or out depending on the siding, without tearing the house apart. The dense-pack method compresses the material so it resists settling inside a closed wall, and as a bonus it noticeably quiets sound between rooms.

Get a measured, written quote

Every blown-in estimate names the material, the target depth and the square footage covered. Call 262-403-8625 or use the quote form to schedule a free attic or wall inspection anywhere in the Lake Country, including Sussex, Pewaukee and Oconomowoc.

Questions

Common questions

Cellulose or fiberglass: which is better for a Wisconsin attic?

Both perform well in cold climates. Cellulose packs tighter around framing and usually costs less installed; fiberglass absorbs almost no moisture and holds its loft longer. We install both and recommend based on your attic, not our inventory.

How deep should my Hartland attic insulation be?

Climate zone 6A attics target roughly R-49 to R-60, which works out to about 14 to 20 inches of blown-in material depending on the product. We measure what is there and quote the added depth in writing.

Can you blow insulation into my existing walls?

Yes. Dense-pack blown-in material fills closed wall cavities through small holes that are patched afterward. It is the standard way to insulate older Lake Country homes without opening the walls up.

Want to know what your project would cost?

We measure the space and quote the material and depth in writing before any work is scheduled.

Free written estimates • No obligation • Local team

Call Now